Iei access control keypad manualKeypad 212w outdoor linear flush iei mount gokeyless resistant indoor weather Wiring diagram to maglock iei keypadIei 212se keypad programming manual / 1. Keypad iei 212i programming diagramsKeypad wiring diagram iei alarm wire gsm system module take standalone manual Iei 232 keypadIei 212se sealed environmental keypad. Iei Keypad Programming Manual Check Details Iei 212i keypad wiring diagram Linear 212w flush mount outdoor keypadIei keypad 212r indoor / outdoor surface-mount ruggedized Keypad ieiWiring diagram to maglock iei keypad. Wiring keypad diagram iei keypads Iei technology 210upc-v312 user manual pdf download Keypad iei 212r ruggedized Iei 212 series installation operating instructionsĪccess control keypad manual ieiIei keypad programming instructions Linear 232r indoor / outdoor surface-mount ruggedized keypadWiring keypad iei maglock diagram. Step 2: Connect the Brown (Normally Open) Relay wire from the 212iL harness to the Normally closed connection on the Door position switch.Keypad iei Keypad access control iei kaba lock gokeyless wiegand electronics locks door manual Keypad iei wiring 212w diagram ilw programming standalone installation Wiring Diagram To Maglock Iei Keypad - Wiring Diagram Schemas Step 1: Connect the Blue (Common) Relay wire from the 212iL harness to the Common connection on the door position switch. Shunting a Normally Closed Zone: (see below) Step 3: Splice together the Black Negative voltage wire on the 212iL harness (negative voltage coming from the power supply) to the Negative connection on the Electric door strike. Step 2: Connect the Brown (Normally Open) wire from the 212iL harness to the Positive voltage connection on the Electric door strike. (Until you supply the common leg of the relay with voltage). This means that there is no voltage running through the relay. The 212iL is equipped with a Form C, Dry contact relay on board. If you are sharing the same DC voltage power supply with the 212iL and the Electric Strike, (that is to say if you have only one power supply for both the 212iL and the lock device), you need to run voltage through the common (Blue) wire on the 6 conductor wire harness of the 212iL. Wiring to an Electric Strike: (see below) Step 3: Splice together the Black Negative voltage wire on the 212iL harness (negative voltage coming from the power supply) to the Negative connection on the Magnetic lock. Step 2: Connect the White /Yellow wire (Normally Closed) from the 212iL harness to the Positive connection on the Magnetic lock. (Positive voltage coming from the power supply.) Step 1: Splice together the Blue Relay Common wire from the 212iL harness to the Red wire on the 212iL harness. The reason is that the 212iL is equipped with a Form C, Dry contact relay on board. If you are sharing the same DC voltage power supply with the 212iL and the magnetic lock, (that is to say if you have only one power supply for both the 212iL and the lock device), you need to run voltage through the common (Blue) wire on the 6 conductor wire harness of the 212iL. Next you will need to attach the relay wires (white/yellow, blue, and brown) to the wire run that is connected to the locking device. Attach the 6-conductor wire harness to the plug in connector on the back of the 212iL.Ģ. Temperature Tolerance: Standard, -20 ° to 130☏.ġ. Maximum Current Draw allowed voltages: 140mA. Operating Voltages: 12-24 VDC only on input voltage. The 212iL should be mounted to a standard single gang electrical box (with the small slot in the trim ring facing down), but it also is able to mount directly to a flat indoor surface with the provided mounting screws. Be sure that the 212iL is mounted indoors ONLY! Mounting height is the same for an electrical switch, 48" on center. Select the appropriate location for the 212iL. Taking this inventory will familiarize you with the components as well as ensure that you have a complete parts list. Please check the contents of this package and verify all components in the packing list are present. Q Section 1: Unpacking and checking the packing listĢ 1 1/4" black, socket cap flat head machine screwsĢ 1 1/4" black, Phillips flat head sheet metal screws V Programmable 00-99 Second Relay Activation Time Single Unit KeypadControl Installation Manual
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |